Back Off Brake Light Signal Module The BackOFF MC Brake light signal module automatically flashes the brake light to capture the attention of following drivers. When installed the motorcycles brake light becomes significantly more noticeable because the brake light modulates three short flashes followed by one steady-on pulse of four seconds. This pattern automatically repeats itself as long as the brakes are applied. Specifications:12V DC max. capacity 10A Sealed weather resistant heat sink case. 2-14 inch long x 58 inch high x 1-58 inch wide
Part Number: 1001 CAN$29.73
Back Off Brake Light Signal Module This compact solid state electronic module converts your ordinary brake lights into your choice of two attention getting visual alerting signals when you apply your brakes: User Selected Mode One:Emit a visual signal of 3 short light flashes followed by 1 long light flash 3.5 seconds. The signal automatically repeats itself as long as the brakes are applied. This pattern is not random but has been selected because of its ability to retain following drivers attention. BUser Selected Mode Two:BEmit a visual signal of 5 short flashes followed by a steady on light that remains steady on as long as the brakes are applied. bOptional:BMotorcycle Emergency Flasher or Automobile Back-Up Flasher. Most states drivers handbooks recommend that you flash your brakes when slowing or stopping. The BackOFF-XP automatically facilitates compliance and enhances safety. Install the BackOFF-XP and see how much more effective your brake light can be. BFeatures:B Easy Installation- Simply install the BackOFF-XP Module in line with the brake light wire leading to the brake light and connect a ground wire. Large power capacity- 12 volts DC Maximum Capacity 10 Amps Compact size- 2-14L x 1-58W x 58H Sealed Weather Resistant heat sink case.
Part Number: 1004 CAN$33.65
Back Off Wig Wag Brake Light Flasher Create more visibility and conspicuity when you are stopped or stopping when you install the BackOFF-Wig Wag Module. This compact solid state electronic module converts your ordinary brake lights into your choice of two attention getting visual alerting signals: User Selected Mode One:Emits 5 alternating quick flashes of the left and right brake lights followed by 3 short flashes and 4 short flashes of both brakes lights. The 4 short flashes automatically repeats itself as long as the brakes are held.bUser Selected Mode Two:bEmits a visual signal of 5 alternating quick flashes of the left and right brake lights followed by 3 short flashes of both brake lights and then the brake light remains steady until the brake is released. Most states drivers handbooks recommend that you flash your brakes when slowing or stopping. The BackOFF-Wig Wag automatically facilitates compliance and enhances safety. Install the BackOFF-Wig Wag and see how much more effective your brake light can be. bFeatures:b Easy Installation- Simply install the BackOFF-Wig Wag Module in line with the brake light wire leading to the brake light and connect a ground wire. Large power capacity- 12 volts DC Maximum Capacity 10 Amps Compact size- 2-14 inch long x 1-58 inch wide x 58 inch high Sealed Weather Resistant heat sink case. Limited Warranty- One Year
Part Number: 1009 CAN$33.65
Black LED License Plate Frame - with Integrated Turn Signals Dual Row Features dual-function red LED brakerunning lights and single-function amber LED turn signals. Die-cast aluminum frame with single or dual row integrated turnbrake LED. Accepts most 4 x 7 inch license plates may require redrilling license plate. Includes complete instructions and wiring diagram. Available with chrome or black powder-coat finish chrome version also available with custom design. Optional chrome mounting hardware kit sold separately. Made in the U.S.A.
Part Number: 2629 CAN$83.8
Black LED License Plate Frame - with Integrated Turn Signals Single Row Features dual-function red LED brakerunning lights and single-function amber LED turn signals. Die-cast aluminum frame with single or dual row integrated turnbrake LED. Accepts most 4 x 7 inch license plates may require redrilling license plate. Includes complete instructions and wiring diagram. Available with chrome or black powder-coat finish chrome version also available with custom design. Optional chrome mounting hardware kit sold separately. Made in the U.S.A.
Part Number: 2603 CAN$58.72
Chrome Acorn Mounting Kit - for LED License Plate Frame These hardware kits are used to fasten the license plate frames to the motorcycle license plate bracket. You can select from a variety of styles that best enhance the appearance of your frame. Each hardware kit contains 4 of the appropriate screws nuts and washers for license plate installation.Use With Frames:SD-2601SD-2602SD-2603SD-2628SD-2629
Part Number: 04001 CAN$8.58
Chrome LED License Plate Frame - with Integrated Turn Signals Dual Row Features dual-function red LED brakerunning lights and single-function amber LED turn signals. Die-cast aluminum frame with single or dual row integrated turnbrake LED. Accepts most 4 x 7 inch license plates may require redrilling license plate. Includes complete instructions and wiring diagram. Available with chrome or black powder-coat finish chrome version also available with custom design. Optional chrome mounting hardware kit sold separately. Made in the U.S.A.
Part Number: 2628 CAN$86.15
Chrome LED License Plate Frame - with Integrated Turn Signals Single Row Features dual-function red LED brakerunning lights and single-function amber LED turn signals. Die-cast aluminum frame with single or dual row integrated turnbrake LED. Accepts most 4 x 7 inch license plates may require redrilling license plate. Includes complete instructions and wiring diagram. Available with chrome or black powder-coat finish chrome version also available with custom design. Optional chrome mounting hardware kit sold separately. Made in the U.S.A.
Part Number: 2601 CAN$58.72
Chrome LED License Plate Frame Custom Design - with Integrated Turn Signals Single Row Features dual-function red LED brakerunning lights and single-function amber LED turn signals. Die-cast aluminum frame with single or dual row integrated turnbrake LED. Accepts most 4 x 7 inch license plates may require redrilling license plate. Includes complete instructions and wiring diagram. Available with chrome or black powder-coat finish chrome version also available with custom design. Optional chrome mounting hardware kit sold separately. Made in the U.S.A.
Part Number: 2602 CAN$58.72
Classic Dual LED Motorcycle Frame Black These high intensity LED products are designed to give greater visibility and conspicuity to your motorcycle. They are unique because they have been engineered to function in both high and low intensity brightness for a multitude of applications. Because many motorcycles have only one brakerunning light bulb these units can easily be used as back-up brake and running lights providing you a greater degree of safety. Mount these beautifully crafted license plate frames and give your bike an excellent finished appearance compared to an otherwise obtrusive license plate. Features: Unique Dual Function Brightness LEDs - Can be operated in low or high intensity brightness Choice of Quality Finish - Brilliant Mirror Chrome SD-2028 and Black Powder Coat. Low Power Requirements - 12V DC 14 Amp Easy Installation - Includes complete instructions and wiring diagram. Ultra Bright High Intensity LEDsbDimensions:bStandard - will fit 49 US states license plates 7-316 inch x 4-14 inch. Measurement from center to center is 5-34 inch x 2-34 inch. Slight re-drilling or filing of bolt holes may be required. Plate may need to be notched for wire pass through.
Part Number: 2029 CAN$66.56
Classic Dual LED Motorcycle Frame Chrome These high intensity LED products are designed to give greater visibility and conspicuity to your motorcycle. They are unique because they have been engineered to function in both high and low intensity brightness for a multitude of applications. Because many motorcycles have only one brakerunning light bulb these units can easily be used as back-up brake and running lights providing you a greater degree of safety. Mount these beautifully crafted license plate frames and give your bike an excellent finished appearance compared to an otherwise obtrusive license plate. Features: Unique Dual Function Brightness LEDs - Can be operated in low or high intensity brightness Choice of Quality Finish - Brilliant Mirror Chrome and Black Powder Coat SD-2029. Low Power Requirements - 12V DC 14 Amp Easy Installation - Includes complete instructions and wiring diagram. Ultra Bright High Intensity LEDsDimensions - Standard will fit 49 US states license plates 7-316 x 4-14. Measurement from center to center is 5-34 x 2-34. Slight re-drilling or filing of bolt holes may be required. Plate may need to be notched for wire pass through.
Part Number: 2028 CAN$66.56
LED License Plate Frame Classic Standard - Chrome These high intensity LED products are designed to give greater visibility and conspicuity to your motorcycle. They are unique because they have been engineered to function in both high and low intensity brightness for a multitude of applications. Because many motorcycles have only one brakerunning light bulb these units can easily be used as back-up brake and running lights providing you a greater degree of safety. Mount these beautifully crafted license plate frames and give your bike an excellent finished appearance compared to an otherwise obtrusive license plate. Unique Dual Function Brightness LEDs - Can be operated in low or high intensity brightness Choice of Quality Finish - Brilliant Mirror Chrome and Black Powder Coat. Dimensions: - Standard will fit most states license plates 7-316 x 4-14. Slight re-drilling of filing or bolt hole may be required.brNote: Other irregular plate sizes for the states of MD WI and OH are available from Country Choppers Signet at 419-655-3441. Please contact them directly if you live in one of these states. Low Power Requirements - 12V DC 14 Amp Easy Installation - Includes complete instructions and wiring diagram. Ultra Bright High Intensity LEDs
Part Number: 2001 CAN$50.89
LED License Plate Frame Custom - Chrome These high intensity LED products are designed to give greater visibility and conspicuity to your motorcycle. They are unique because they have been engineered to function in both high and low intensity brightness for a multitude of applications. Because many motorcycles have only one brakerunning light bulb these units can easily be used as back-up brake and running lights providing you a greater degree of safety. Mount these beautifully crafted license plate frames and give your bike an excellent finished appearance compared to an otherwise obtrusive license plate. Unique Dual Function Brightness LEDs - Can be operated in low or high intensity brightness Choice of Quality Finish - Brilliant Mirror Chrome and Black Powder Coat. Dimensions: - Standard will fit most states license plates 7-316 x 4-14. Slight re-drilling of filing or bolt hole may be required. Other irregular plate sizes are available for: MD WI and OH please call us at 888-302-9789.Low Power Requirements - 12V DC 14 Amp Easy Installation - Includes complete instructions and wiring diagram. Ultra Bright High Intensity LEDs
Part Number: 2002 CAN$50.89
License Plate Frame Classic Black Standard CXS Mount these beautifully crafted license plate frames and give your bike an excellent finished appearance compared to an otherwise obtrusive license plate.Dimensions:Standard - will fit all 50 US states license plates 7-316 inch x 4-14 inch. Measurement from center to center is 5-34 inch x 2-34 inch. Slight re-drilling or filing of bolt holes may be required.
Part Number: 6003 CAN$18.76
License Plate Frame Classic Chrome Standard CXS Mount this beautifully crafted license plate frame and give your bike an excellent finished appearance compared to an otherwise obtrusive license plate.Dimensions:Standard - will fit all 50 US states license plates 7-316 inch x 4-14 inch. Measurement from center to center is 5-34 inch x 2-34 inch. Slight re-drilling or filing of bolt holes may be required.
Part Number: 6001 CAN$18.76
Mounting Hardware Black Flat head w lock nut These hardware kits are used to fasten the license plate frames to the motorcycle license plate bracket. You can select from a variety of styles that best enhance the appearance of your frame. Each hardware kit contains 4 of the appropriate screws nuts and washers for license plate installation.Note: Part number SD-4003 comes as a pair and not as a set of four.
Part Number: 4003 CAN$8.58
Mounting Hardware Chrome Flat head w lock nut These hardware kits are used to fasten the license plate frames to the motorcycle license plate bracket. You can select from a variety of styles that best enhance the appearance of your frame. Each hardware kit contains 4 of the appropriate screws nuts and washers for license plate installation.Note: for use on all Classic Chrome Frames - not for use on Custom Frames
Part Number: 4002 CAN$8.58
Plug and Play Dual H4 Adapter Harness This is the harness you need if your bike has an H4 connector on the headlight. This harness will work with both single and dual headlight motorcycles.This module works with most Harley Davidson Motorcycles or motorcycles that use a Dual Filament Bulb. Please consult your owners manual for your correct bulb type.Note: Requires the Plug and Play Headlight Module SOLD SEPARATELY
Part Number: 1080 CAN$11.71
Plug and Play H7 Japanese Adapter Harness This is the harness you need if your bike has an H7 Japanese connector on the headlight. This harness will work with both single and dual headlight bikes when connected to the Plug and Play Headlight Module.This harness is used on most Japanese motorcycles Honda Yamaha etc. Please consult your owners manual for your correct bulb type.Note: Requires the Plug and Play Headlight Module SOLD SEPARATELY
Part Number: 1082 CAN$15.63
Plug and Play Headlight Module Now there is no need to cut or splice wires in order to install a headlight module on your bikeWith the Plug Play Headlight Module simply select which harness is needed for your bike then plug it all togetherFeatures:bToggle Modulation ON and OFFb - The modulation of the headlight can be toggled on and off by the user at any time. When the bike is started the default is modulation ON. To turn the modulation on or off simply switch your bikes high low beam switch to the opposite position and then back to the original position within one second this can be done with the switch in either the high or low beam position.bAuto Night Shut-Offb - The Diamond Star Headlight Modulator is designed to automatically turn on and off at specific light levels in order to comply with the DOTs regulation of no night time modulation.bTo Switch From Max to Min Modeb - The Diamond Star Headlight Module is equipped with two levels of modulation to meet your visibility requirements. Both are fully DOT compliant. The default level is Max when the bike is turned on but can easily be toggled to Min or back to Max by simply pressing the horn button twice within one second.bHeads Up Alertb - The Diamond Star Headlight Module can be connected to your bikes horn wire in order to add a visual alert to your horns audible alert. Pressing the horn will cause your headlight to modulate for 3 seconds then return to steady on or toggle between min and max mode for 3 seconds if it is already modulating. bPlease Note: as per D.O.T. regulations the Heads Up Alert feature DOES NOT work at nightbbEmergency Headlight Featureb- The Diamond Star Headlight Module is constantly monitoring the bulb that you have selected high beam or low beam. In the event the bulbs should fail the alternate bulbs will instantly be turned on. This switching will only be done once when the bike is turned off and then back on you will not have use of the bulb that failed until it is repaired or replaced. While the Heads-Up Alert fea
Part Number: 1015 CAN$58.72
Plug and Play Single H4 Adapter Harness This is the harness you need if your bike has an H4 connector on the headlight. This harness will ONLY work with a single headlight motorcycle.This module works with most Harley Davidson Motorcycles or motorcycles that use a Dual Filament Bulb. Please consult your owners manual for your correct bulb type.Note: Requires the Plug and Play Headlight Module SOLD SEPARATELY
Part Number: 1083 CAN$10.15
Plug and Play Universal Adapter Harness This harness is to be used on any type motorcycle that does not fall within the other harness provided. This harness does require cutting and splicing of your factory harness similar to the Diamond Star Headlight Modulator.Note: Requires the Plug and Play Headlight Module SOLD SEPARATELY
Part Number: 1084 CAN$10.15
Universal Light Bar 3 inch Black w Amber Lens pair These high intensity LED products are designed to give greater visibility and conspicuity to your vehicle. They are unique because they have been engineered to function in both high and low intensity brightness for a multitude of applications. Because many motorcycles have only one brake running light bulb these units can easily be used as back-up brake and running lights providing you a greater degree of safety. Mount the Universal Light Bar anywhere you want or need more light - on saddle bags tour packs sissy bar rear fender trailer or custom installations. Features: Unique Dual Function Brightness LEDs - Can be operated in low and high intensity brightness Choice of Quality Finish - Brilliant Mirror Chrome and Black Powder Coat. Low Power Requirements - 12V DC 18 Amp Easy Installation Ultra Bright High Intensity LEDs Mounting Hardware and form-fitting gasket includedbDimensions:b3 inch L x 58 inch W x 78 inch H
Part Number: 2042 CAN$40.7
Universal Light Bar 3 inch Black w Red Lens pair These high intensity LED products are designed to give greater visibility and conspicuity to your vehicle. They are unique because they have been engineered to function in both high and low intensity brightness for a multitude of applications. Because many motorcycles have only one brake running light bulb these units can easily be used as back-up brake and running lights providing you a greater degree of safety. Mount the Universal Light Bar anywhere you want or need more light - on saddle bags tour packs sissy bar rear fender trailer or custom installations. Features: Unique Dual Function Brightness LEDs - Can be operated in low and high intensity brightness Choice of Quality Finish - Brilliant Mirror Chrome and Black Powder Coat. Low Power Requirements - 12V DC 18 Amp Easy Installation Ultra Bright High Intensity LEDs Mounting Hardware and form-fitting gasket included bDimensions:b3 inch L x 58 inch W x 78 inchH
Part Number: 2044 CAN$39.14
Universal Light Bar 3 inch Chrome w Red Lens pair These high intensity LED products are designed to give greater visibility and conspicuity to your vehicle. They are unique because they have been engineered to function in both high and low intensity brightness for a multitude of applications. Because many motorcycles have only one brake running light bulb these units can easily be used as back-up brake and running lights providing you a greater degree of safety. Mount the Universal Light Bar anywhere you want or need more light - on saddle bags tour packs sissy bar rear fender trailer or custom installations. Features: Unique Dual Function Brightness LEDs - Can be operated in low and high intensity brightness Choice of Quality Finish - Brilliant Mirror Chrome and Black Powder Coat. Easy Installation Ultra Bright High Intensity LEDs Mounting Hardware and form-fitting gasket included Low Power Requirements - 12V DC 18 AmpbDimensions:b3 inch L x 58 inch W x 78 inch H
Part Number: 2043 CAN$39.14
Universal Light Bar 6 inch Black w Red Lens These high intensity LED products are designed to give greater visibility and conspicuity to your motorcycle. They are unique because they have been engineered to function in both high and low intensity brightness for a multitude of applications. Because many motorcycles have only one brakerunning light bulb these units can easily be used as back-up brake and running lights providing you a greater degree of safety. Mount the Universal Light Bar anywhere you want or need more light - on saddle bags tour packs sissy bar rear fender trailer or custom installations. Features: Unique Dual Function Brightness LEDs - Can be operated in low or high intensity brightness Choice of Quality Finish - Brilliant Mirror Chrome and Black Powder Coat. Low Power Requirements - 12V DC 14 Amp Easy InstallationbDimensions:b6 inch L x 58 inch W x 78 inch H
Part Number: 2010 CAN$33.65
Universal light Bar 6 inch Chrome w Amber Lens These high intensity LED products are designed to give greater visibility and conspicuity to your motorcycle. They are unique because they have been engineered to function in both high and low intensity brightness for a multitude of applications. Because many motorcycles have only one brakerunning light bulb these units can easily be used as back-up brake and running lights providing you a greater degree of safety. Mount the Universal Light Bar anywhere you want or need more light - on saddle bags tour packs sissy bar rear fender trailer or custom installations. Features: Unique Dual Function Brightness LEDs - Can be operated in low or high intensity brightness Choice of Quality Finish - Brilliant Mirror Chrome and Black Powder Coat. Low Power Requirements - 12V DC 14 Amp Easy InstallationbDimensions:b6 inch L x 58 inch W x 78 inch H
Part Number: 2008 CAN$36
Universal Light Bar 6 inch Chrome w Red Lens These high intensity LED products are designed to give greater visibility and conspicuity to your motorcycle. They are unique because they have been engineered to function in both high and low intensity brightness for a multitude of applications. Because many motorcycles have only one brakerunning light bulb these units can easily be used as back-up brake and running lights providing you a greater degree of safety. Mount the Universal Light Bar anywhere you want or need more light - on saddle bags tour packs sissy bar rear fender trailer or custom installations. Features: Unique Dual Function Brightness LEDs - Can be operated in low or high intensity brightness Choice of Quality Finish - Brilliant Mirror Chrome and Black Powder Coat. Low Power Requirements - 12V DC 14 Amp Easy InstallationbDimensions:b6 inch L x 58 inch W x 78 inch H
